4 Cylinder Race and High Performance
| Blocks | Cleaning | $55.00 |
| Inspecting for cracks (MT Magnetic particle) | $25.00 | |
| Pressure check for leaks | $55.00 | |
| Check line bore | $35.00 | |
| Check deck for bad areas and low places | n/c | |
| Check piston to deck height using your crank, rod and pistons | $65.00 | |
| Check cylinder wear | n/c | |
| Cylinder boring (up to 1MM) | $85.00 | |
| Cylinder boring (1MM-3MM) | $100.00 | |
| Installing sleeve and finish to size (most cases) Straight wall sleeve (sleeve extra) Call on Prices to install flanged sleeves | $80.00 | |
| Block decking (milling head surface) | $65.00 | |
| "O" ring cylinders (wire included) copper wire | $60.00 | |
| "O" ring cylinders (wire included) stainless wire | $70.00 | |
| Line Hone Block with 5 main caps (unless burned, loose, or mismatched caps) | $100.00 | |
| with Girdle Cap Assembly | $140.00 | |
| Hone cylinders (Rigid hone) (all 4) | $40.00 | |
| Install cam bearings (Block) | $35.00 | |
| Install freeze plugs | $20.00 | |
| Ultrasonic test cylinder walls for thickness | $45.00 | |
| Make detailed check of above | $90.00 | |
| Blocks with studs may cost extra | ||
| Cranks | Clean (some jobs will require this) | $25.00 |
| Check crank for size, straightness, and polish | $35.00 | |
| Chamfer oil holes and polish | $35.00 | |
| Magnaflux-magnaglo inspection for cracks (must be cleaned) | $45.00 | |
| Cross drill mains (includes chamfer and polish) | $85.00 | |
| Lighten or Knife edge (Priced on Request) | ||
| Welding worn or burned journals (per journal) | $150.00-300.00 | |
| Offset grinding (Price on request) | ||
| Correct Index (Price on request) | ||
| Rods | Check big end for round per set | $25.00 |
| Check for straightness per set | $15.00 | |
| Resizing big end per set | $55.00 | |
| Magnaflux-magnaglo Inspection for cracks | $35.00 | |
| Side clearance (one side) | $40.00 | |
| Balancing (Complete balance job includes this) | $35.00 | |
| Remove and replace bushings and pin fit (Labor) | $35.00 | |
| Pistons | Remove and replace on rods (Press type) | $40.00 |
| Fly cutting for valve clearance | $85.00 | |
| Pin fitting for additional clearance | $25.00 | |
| Mill domes | $50.00 | |
| Balancing (Complete balance job includes this) (set) | $30.00 | |
| Flywheel |
Grinding to true Flat type |
$50.00 |
|
Step type |
$55.00 | |
| Balance flywheel | $35.00 | |
| Lighten and Balance | $85.00-$125.00 | |
| Misc. | Check bearing clearance (1 rod and 1 main) | $45.00 |
| (If we do the above when we are line boring or rod resizing, we can usually make your bearing clearance any size you want) | ||
|
Clean oil pan $20.00 |
Clean All $50.00 |
|
| Clean valve cover $15.00 | ||
| Clean timing cover $8.00 | ||
| Clean bolts and push rods $20.00 | ||
| Thread repair and heli-coil | By Time |
All Prices are subject to change.
103006